Current location: Home > News information > Industry Information
Technical standard for large generators in China to be drafted in Shenzhen
Loading...
2019-10-19
From May 4 to 7, 2016, the first standard drafting working group meeting of National Large Generator Standard Technical Committee will be held in Hongbo Hotel, Shenzhen. This meeting will be sponsored by National Large Generator Standardization Technical Committee and co-organized by Shenzhen Testeck Science And Technology Co., Ltd.

 

Notice on convening the first standard drafting working group meeting in 2016
Members of the standard drafting working group:
According to the work plan of 2016 and the discussion of the Secretariat, the first standard drafting working group meeting of National Large Generator Standard Technical Committee will be held in Shenzhen from May 4 to 7. Relevant matters of the meeting are hereby notified as follows:

 

一. Contents of the meeting
Prepare and revise the following six standards:

(1) JB/T 10500.1 Embedded thermal resistor for motor Part 1: General provisions, measurement methods and inspection rules
(2) JB/T 10500.2 Embedded thermal resistor for motor Part 2: Technical requirements for platinum thermal resistor
(3) JB/T 10500.3 embedded thermal resistor for motor Part 3: Technical requirements for copper thermal resistor
(4) JB/T 2224 Technical conditions for large AC three-phase four-pole synchronous motor
(5) JB/T 6517 Technical conditions for hydrogen oil-water control system
(6) JB/T XXXX Technical conditions for rectangular silver-copper conductor with unequal wall thickness for rotor of air inner-cooled generator
 
 
二、Meeting arrangement
1. Meeting date: Meeting from May 5to7, 2016, check-in on May 4.
2. Venue: Hongbo Hotel Shenzhen 
3. Address: Post and Telecommunications Conference Center, No. 10, OCT West Street, Nanshan District, Shenzhen (near Happy Valley and OCT Bar Street)
4. Traffic routes:
(1) Shenzhen Bao’an Airport: Take the metro Luobao Line (Line 1) to get off at OCT Station (Exit B3) and then walk for 800 meters northwards (the whole trip takes about 1.5 hours).
(2) Shenzhen Railway Station: Take the metro Luobao Line (Line 1) to get off at OCT Station (Exit B3) and then walk for 800 meters northwards (the whole trip takes about 1 hour).
(3) Shenzhen North Railway Station: Take the metro Longhua Line (Line 4), transfer and take Luobao Line (Line 1) to get off at OCT Station (Exit B3) and then walk for 800 meters northwards (the whole trip takes about 1 hour).
(4) Shenzhen West Railway Station: Take Bus No. b623/58,transfer and take Luobao Line (Line 1) at Daxincun Station to get off at OCT Station (Exit B3) and then walk for 800 meters northwards (the whole trip takes about 1 hour).
(5) Shenzhen East Railway Station: Take Bus No. m403/307 to get off at Kingglory Plaza Station, walk for 200 meters to Guomao Station, transfer and take Luobao Line (Line 1), get off at OCT Station (Exit B3) and then walk for 800 meters northwards (the whole trip takes about 1 hour).

 

三 、Participants

See Annex 1 for the list of participants.

 

contacts:
Zhou Mi (Secretariat)
Tel: 0451-82873290
Mobile: 13359718075
E-mail: zhoumi_hec@163.com
Zhao Ziming (Shenzhen Testeck Science & Technology Co., Ltd.)
Mobile: 13923874703
E-mail: zzm@testeck.com
Annex: 1. List of participants
2. Receipt
2016.4.12
Secretariat Of National Large Generator Standardization Technical Committee
April 12, 2016
 
Annex 11:
List of participants
I. JB/T 10500- - XXXX Series standards for embedded thermal resistor for motor (Part 33)
No.   Name   Work unit    Position/title
1. Wang Tingshan, chief engineer/professor of engineering of Generator Plant of Shanghai Electric Power Plant Equipment Co., Ltd.
2. Gu Yue, director/professor of engineering of Generator Plant of Shanghai Electric Power Plant Equipment Co., Ltd.
3. Su Buwei, engineer of Generator Plant of Shanghai Electric Power Plant Equipment Co., Ltd.
4. Chen Jingyi, group leader/senior engineer of Design Department of Harbin Electric Machinery Co., Ltd.
5. Wen Xingli, senior engineer of Dongfang Electric Co., Ltd.of Dongfang Electric Group
6. Yang Ming, senior engineer of Harbin Institute of Large Electrical Machinery
7. Wang Bin, deputy chief engineer/professor of engineering of Shanghai Electric Machinery Co., Ltd. of Shanghai Electric Group
8. Chen Jianguo, director/engineer of Harbin Electric Power Equipment Co., Ltd.
9. Huang Shuming, chief engineer of Shenzhen Testeck Science And Technology Co., Ltd.
10. Huang Jinghua, general manager of Changzhou Qingliang Instrument Co., Ltd.
11. Li Zuobin, senior engineer of China Nuclear Power Engineering Co., Ltd.
 


II. B/T 2 224- - XXXX Technical conditions for large AC three-phase four- pole synchronous motor
1. To be determined, Lanzhou Electric Machinery Co., Ltd., to be determined.
2. Chen Jianguo, director/engineer of Harbin Electric Power Equipment Co., Ltd.
3. Zhong Weilin, engineer of Dongfang Electric Co., Ltd.of Dongfang Electric Group
4. Wang Bin, deputy chief engineer/professor of engineering of Shanghai Electric Machinery Co., Ltd. of Shanghai Electric Group
5. Sun Yutian, deputy director/professor of engineering of Harbin Institute of Large Electrical Machinery
6. To be determined, Beijing Jingcheng New Energy Co., Ltd., to be determined.
7. Wang Yu, manager of Chief Engineer Office of Tellhow Shenyang Electric Machine Co., Ltd. 

 
III. JB/T  6517- - XXXX Technical conditions for hydrogen oil water control system
1. Liang Xun, chief engineer of Harbin Electric Machinery Co., Ltd.
2. Qi Minglu, chief engineer of Harbin Electric Machinery Co., Ltd.
3. Sun Junbo, deputy manager of Harbin Electric Machinery Co., Ltd.
4. Wu Qingjun, deputy chief engineer of Engineering Department of Shanghai Turbogenerator Co., Ltd. 
5. Li Ende, deputy chief designer of Motor Technology Department of Beijing Beizhong Turbogenerator Co., Ltd.
6. Dai Ji, chief engineer of Dongfang motor control equipment Co., Ltd.
7. Li Zuobin, senior engineer of China Nuclear Power Engineering Co., Ltd.
 

IV. JB/T XXXX- - XXXX Technical conditions for rectangular silver-copper conductor with unequal wall thickness for rotor of air inner-cooled generator
1. Lu Qijie, director/senior engineer of Shandong Qilu Electric Machinery Manufacturing Co., Ltd. (Shandong Jinan Power Equipment Factory)
2. Wang Tongzhang, senior engineer of Shandong Qilu Electric Machinery Manufacturing Co., Ltd. (Shandong Jinan Power Equipment Factory)
3. Wei Jingsheng, senior engineer of Shandong Qilu Electric Machinery Manufacturing Co., Ltd. (Shandong Jinan Power Equipment Factory)
4. Huo Yan, engineer of Harbin Electric Power Equipment Co., Ltd.
5. Chen Jingyi, group leader/senior engineer of Design Department of Harbin Electric Machinery Co., Ltd.
6. Dong Hongda, deputy chief designer/senior engineer of Generator Plant of Shanghai Electric Power Plant Equipment Co., Ltd..
7. Li Jixia, /senior engineer of Shanghai Electric Machinery Co., Ltd. of Shanghai Electric Group 
 
Share to: